ZONE 5’7: 170 x 47 cm | 24,7 l
ZONE 5’10: 178 x 48,3 cm | 27,8 l
The SPLEENE ZONE waveboard is at ease in waves. Whether your home wave spot or a dream location on this planet. Built in classic PU construction – for the real and lively surf feeling!
- Pure surf feeling
- Low weight
- High comfort and flex
- Rail to rail surfing
- Direct feedback & control
Handmade in premium quality by the shapers of FATUM in Portugal. Each waveboard is unique, made in Europe.
Available in 90 days, delivery time 2-5 days
Enter the Zone!
A wall of water rises slowly behind your back … you notice how your board speeds up. You are totally focused on the moment – you are one with the wave!
Highlights des SPLEENE ZONE
Real surf feeling and good comfort
The SPLEENE waveboards have a natural liveliness and a pleasant flex. This allows real surf feeling, without compromise. This is achieved through the use of a special, hand-finished PU core, as it is also used in classic surfboards. Every turn with a SPLEENE waveboard is a real pleasure and even choppy conditions turn into pleasure. So you enjoy long surf sessions to the fullest.
The harmonious adjustment between the tail and the center of the board make the ZONE a wave allrounder. In small waves it takes enough thrust and shines in large waves with a harmonious agility.
Thanks to the good controllability and the comfortable width of the ZONE waveboard, snappy turns at the top of the wave are no problem. The SPLEENE ZONE quickly finds guidance - even in the wind waves we are used to from the north of Europe.
Rail to rail surfing
With the ZONE you can pull fantastic bottom turns into the wave and shred them with radical cut backs. The thinning rails in the tail of the board give you extra grip. The ZONE Waveboard takes the edge change playfully. The PU construction provides the necessary smoothness in bottom turn - no matter what radius - and restoring power as well as feedback in the cut back.
This is exactly how surfing in the wave must be!
PU construction with stringer
The SPLEENE waveboards are handmade in PU construction, like a classic surfboard. In the last 50 years different construction methods with different materials have been tested in surfing and windsurfing. Our opinion and that of the experts is clear: The PU construction is the only method to build lively waveboards with real surf feeling for kiting.
Also wood could never be completely replaced over the decades. In every good ski, sowboard or kiteboard there is wood! So also in the SPLEENE waveboards: A wooden stringer runs through the middle of the boards and makes the setup perfect.
The construction requires intensive handwork and many years of experience. That's why the SPLEENE waveboards are made in small series by FATUM in Portugal. The PU core is specially optimized for board building - only a few shapers have access to this quality.
The result plays in a different league than conventional waveboards, which are manufactured in industrial construction as mass-produced goods!
>By using PU foam, wood stringer and polyester resin you get a piece of jewelry that will give you a lot of pleasure. And even in case of damage you don't have to worry. The PU core won't pull water and you don't have to end your session right away. With polyester resin, damage can be easily repaired.
Boring white? On the contrary! The SPLEENE waveboards come in bright colors and are a special eye-catcher. The colors are applied by hand directly to the core and lie under the fiberglass on the finished waveboard. Also the SPLEENE decals are under the fiberglass and will stay with you forever.
Thruster FCS II setup with reinforcements
The ZONE Waveboard has a thruster setup and offers you the optimal balance of agility and guidance. The ZONE Waveboard allows you smooth but also radical turns and moves.
The FCS II system is used for the fin system - lightning-fast, tool-free assembly and a huge fin selection. The FCS-II Fin Plugs have been additionally reinforced during installation. For maximum durability and a robust setup - perfect for the demands of wave kitesurfing.
Range of use of the CROSS waveboards
The best accessories for your ZONE
Our EVA pads from WMFG provide you with the best possible grip. Thanks to the pattern you have the feeling that the Waveboard “sticks” to your feet, even in radical maneuvers. You can position the pads individually. So nothing is left to chance. Or you choose to go with Surfwax – the choice is yours.
The ZONE comes with a thruster setup and is compatible with all FCS II Finnen. The fins we offer are well adapted to the ZONE and you have the choice between the sizes M and L. The size M is optimal for the ZONE 5’7 – or if you prefer a loose feeling with the Zone 5’10. The fins in size L are optimal for the Zone 5’10.
In addition to the FCS II fins, you can also use FCS I fins with the FCS adapter – so you can get fins in the farthest corner of the world if you need a replacement.
You like riding in straps? So does the ZONE!
Thanks to the M6 threads you can easily mount the SPLEENE Straps. 3 different positions on the front and 2 on the back allow you to find your sweet spot. And thanks to the comfortable straps you can ride one wave after the other – until the sun goes down.